Aluminum 7050-T73511; 7050-T73510


Subcategory: 7000 Series Aluminum Alloy; Aluminum Alloy; Metal; Nonferrous Metal

Close Analogs:

Composition Notes:
Aluminum content reported is calculated as remainder.
Composition information provided by the Aluminum Association and is not for design.

Key Words: UNS A97050; ISO AlZn6CuMgZr; Aluminum 7050-T73510; AA7050-T73511

Component   Wt. %
Al87.3 - 90.3 
CrMax 0.04 
Cu2 - 2.6 
FeMax 0.15 
Component   Wt. %
Mg1.9 - 2.6 
MnMax 0.1 
Other, eachMax 0.05 
Other, totalMax 0.15 
Component   Wt. %
SiMax 0.12 
TiMax 0.06 
Zn5.7 - 6.7 
Zr0.08 - 0.15 

Material Notes:
Data points with the AA note have been provided by the Aluminum Association, Inc. and are NOT FOR DESIGN.

Physical PropertiesMetricEnglishComments
Density2.83 g/cc0.102 lb/in³ AA; Typical

Mechanical Properties
Hardness, Brinell132132 500 kg load with 10 mm ball. Calculated value.
Hardness, Knoop166166 Converted from Brinell Hardness Value
Hardness, Rockwell A49.849.8 Converted from Brinell Hardness Value
Hardness, Rockwell B8080 Converted from Brinell Hardness Value
Hardness, Vickers151151 Converted from Brinell Hardness Value
Ultimate Tensile Strength496 MPa72000 psi AA; Typical
Tensile Yield Strength434 MPa63000 psi AA; Typical
Elongation at Break12 %12 % AA; Typical; 1/2 in. (12.7 mm) Diameter
Modulus of Elasticity71.7 GPa10400 ksi AA; Typical; Average of tension and compression. Compression modulus is about 2% greater than tensile modulus.
Poisson's Ratio0.330.33 
Shear Modulus26.9 GPa3900 ksi 
Shear Strength290 MPa42100 psi Calculated value.

Electrical Properties
Electrical Resistivity4.3e-006 ohm-cm4.3e-006 ohm-cm 

Thermal Properties
CTE, linear 20°C23.6 µm/m-°C13.1 µin/in-°F 20-100ºC
CTE, linear 250°C25.4 µm/m-°C14.1 µin/in-°F Average over the range 20-300ºC
Specific Heat Capacity0.86 J/g-°C0.206 BTU/lb-°F 
Thermal Conductivity155 W/m-K1080 BTU-in/hr-ft²-°F Estimated from other heat treatments.
Melting Point524 - 635 °C975 - 1170 °F For homogeneous wrought material. Eutectic for nonhomogeneous wrought or as-cast material that has not been heat treated is 465ºC.
Solidus524 °C975 °F For homogeneous wrought material. Eutectic for nonhomogeneous wrought or as-cast material that has not been heat treated is 465ºC.
Liquidus635 °C1170 °F 

Processing Properties
Annealing Temperature413 °C775 °F 
Solution Temperature477 °C890 °F 
Aging Temperature121 - 177 °C250 - 350 °F 

References for this datasheet.


Some of the values displayed above may have been converted from their original units and/or rounded in order to display the information in a consistant format. Users requiring more precise data for scientific or engineering calculations can click on the property value to see the original value as well as raw conversions to equivalent units. We advise that you only use the original value or one of its raw conversions in your calculations to minimize rounding error. We also ask that you refer to MatWeb's disclaimer and terms of use regarding this information. MatWeb data and tools provided by MatWeb, LLC.